BGGDH - REAR VIEW MIRROR ADHESIVE
- MSDS: BGGDH
- Manufacturer: SUPER GLUE CORP
- Product Name: REAR VIEW MIRROR ADHESIVE
- National Stock Number: 2540-01-033-1831
Product Identification
Product ID:REAR VIEW MIRROR ADHESIVE
MSDS Date:11/25/1985
FSC:2540
NIIN:01-033-1831
MSDS Number: BGGDH
Responsible Party
HOLLIS, NY 11423
US
Emergency Phone: 212-454-4747
Info Phone: 800-221-4478
Preparer: SUZANNE FOSTER
Cage: 0ACS9
Contractor
Telephone: 800-221-4478
Cage: 0ACS9
Ingredients
ALIPHATIC ACID
Fraction By Weight: <2%
ACGIH TLV: NOT ASSIGNED
ACRYLIC ACID
Fraction By Weight: <5%
ACGIH TLV: 10 PPM
ORGANIC PEROXYESTER
Fraction By Weight: <3%
ACGIH TLV: NOT ASSIGNED
Hazards
LD50 LC50 Mixture:NOT REPORTED BY MANUFACTURER.
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN AND EYE IRRITATION MAY OCCUR.
HIGH LEVELS OF ACRYLIC ACID VAPORS CAUSE NOSE AND THROAT
IRRITATION.
Effects of Overexposure:SKIN AND EYE IRRITATION;HIGH LEVEL OF ACRYLIC
ACID VAPORS CAUSE NOSE & THROAT IRRITATION.
Medical Cond Aggravated by Exposure:NONE STATED BY THE MANUFACTURER.
First Aid
First Aid:EYE:FLUSH WITH COPIOUS AMOUNT OF WATER FOR SEVERAL MINUTES.
GET MEDICAL ATTENTION. SKIN: WASH WITH SOAP AND WATER. DO NOT USE
ORGANIC SOLVENTS FOR CLEAN-UP AS THEY MAY DRY OR IRRITATE THE SKIN
AND ACT AS A CARRIER FOR CHEMICAL ABSORBTION. INHALATION: REMOVE
TO FRESH AIR,GIVE ARTIFICIAL RESPIRATION IF NEEDED; INGESTION: LOW
TOXICITY. GET MEDICAL ATTENTION.
Fire Fighting
Flash Point Method:PMCC
Flash Point:>200F/93C
Extinguishing Media:CARBON DIOXIDE, FOAM, DRY CHEMICAL, OR WATER FOG.
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR SELF-CONTAINED
BREATHING APPARATUS.
Unusual Fire/Explosion Hazard:TOXIC FUMES (OXIDES OF CARBON AND
NITROGEN) MAY BE EVOLVED UPON EXPOSURE TO HEAT OR OPEN FLAME.
Accidental Release
Spill Release Procedures:DIKE AREA TO PREVENT SPREADING.ABSORB MATERIAL
WITH VERMICULITE, SAND OR OTHER INERT ABSORBING MATERIAL. PUT IN
CLOSED CONTAINER. DISPOSE OF AS CHEMICAL WASTE.
Neutralizing Agent:NONE STATED BY THE MANUFACTURER.
Handling
Handling and Storage Precautions:MATERIAL SHOULD BE HANDLED AND STORED
IN A COOL (50-80F), DARK PLACE. TEMPERATURES OVER 120F SHOULD BE
AVOIDED FOR MAXIMUM SHELF LIFE.
Other Precautions:SLOW POLYMERIZATION,WITH POSSIBLE HEAT
GENERATION,WILL OCCUR IN DIRECT SUNLIGHT AND AT TEMP APPROX 130F OR
HIGHER.
Exposure Controls
Respiratory Protection:POSITIVE FRESH AIR EXHAUST SHOULD BE PROVIDED IN
THE WORK AREA. RESPIRATORY EQUIPMENT IS UNNECESSARY IN NORMAL USE,
IF THE AREA IS PROPERLY VENTILATED.
Ventilation:ADEQUATE VENTILATION
Protective Gloves:IMPERVIOUS
Eye Protection:CHEMICAL SAFETY GLASSES OR GOGGLES
Other Protective Equipment:NONE
Supplemental Safety and Health
MSDS DATED 11-25-85. PART A OF A TWO-PART KIT,PART B IS "ACTIVATOR".
Chemical Properties
HCC:N1
Vapor Pres:6 @30C
Vapor Density:>1 AIR=1
Spec Gravity:1.08
Solubility in Water:INSOLUBLE
Appearance and Odor:AMBER LIQUID
Percent Volatiles by Volume:<0.1
Stability
Stability Indicator/Materials to Avoid:YES
STRONG ALKALI, OXIDIZERS, AND REACTIVE METALS.
Stability Condition to Avoid:OPEN CONTAINERS,EXPOSURE TO HEAT,OR OPEN
FLAME WHICH CAN CAUSE THERMAL DECOMPOSITION.
Hazardous Decomposition Products:OXIDES OF CARBON & NITROGEN,HCL,AND
PHOSGENE
Disposal
Waste Disposal Methods:CONTACT YOUR LOCAL ENVIRONMENTAL OFFICER. KEEP
IN COVERED DRUMS, PENDING DISPOSAL. HANDLE & DISPOSE IN FULL
COMPLIANCE WITH ALL APPLICABLE FEDERAL, STATE, AND LOCAL
REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.